Concrete plant QUICK BETON-55
242 507 BYN




Enquire conditions
and delivery time

We'll call you back within 15 minutes

Specify your requirements

Send prices and terms of delivery
51 362 BYN
- BP-2G-1200 Twin-shaft concrete mixer
- Пневмозатвор "Camozzi" - двойной
- Connection set for pneumatic equipment
- Manual lubrication system: grease press UMETA (Germany)
- Armor shift flake type. Material: cast iron wear 15 mm
- Спицы усиленные (стальное литье) крепление типа "кулак"
- Changeable blades. Material: ЧХ16Н2Т cast iron (chromic high alloy wear-resistant)
- Electricity to connect the remote control
- Maintenance kit (three armor, blade, needle)
- Concrete mixer machinery certificate
72 993 BYN
- Mounting frame, mobile. Installation without foundation
- Design enhanced, adapted for the discharge of concrete on the height of 4500 mm
- mixer platform with supporting structures
- Ladders for equipment maintenance
- Fence along the perimeter
- Staircase with handrails
- Funnel for unloading concrete with rubber guide
- platform band
- Fastening construction for pipes and electric cables
- Coating: shotblasting, double coloration with drying chamber
65 959 BYN
- Setting the frame supporting RO-75L. Installation without foundation.
- Inert materials hopper 4 pieces of 10 cubic meters. meters (4 x 10)
- Brush for cleaning the conveyor belt
- Herringbone tape 800 / 24000mm
- Lower spiral roller (to prevent descent of tape)
- Пневмораспределители "Camozzi" (Италия) - 4 шт.
- Фильтр-регулятор "Camozzi" - 1 шт.
- Vibrators OLI MVE 300 3 - 8 pcs.
- Vibroplastiny with shock-absorbing cushions
- Conveyor inert materials (0-3800 kg dose).
- Lined drive motor drum 18.5 kW with soft-start system
- Drum tension station
- Тензодатчики 3 тонны "CAS" (Ю. Корея) - 4 шт.
- Коробка соединительная "CAS" (Ю. Корея)
- Signal amplifier - weight sensor
18 517 BYN
- Mounting frame (powder coating). Weight - 200 kg
- Cement dispenser, dosage - 500 kg (powder coating):
- Two inlet nozzles for screw conveyors (one is covered by a cap)
- Connecting outer sheath with collar clamps
- Overpressure system
- Разгрузочная дисковая пневмозаслонка "Camozzi" ∅200
- CAS BSA500 strain sensors - 3 pieces
- Signal amplifier - weight sensor
- Пневмораспределители "Camozzi" (Италия) - 3 штуки
- OLI MVE 21 vibrator - 1 piece
- Water dispenser, dosage - 250 liters (powder coating):
- CAS BSA500 strain sensors - 3 pieces
- Разгрузочная шаровая пневмозаслонка ∅50 "Camozzi"
- Calpeda NM 50-12 FВ Pump
- Water and chemical agents multipoint injection system
- Signal amplifier - weight sensor
- Chemical additives dispenser, dosage - 30 liters, made of stainless steel:
- CAS BСA100 strain sensor - 1 piece
- Разгрузочная шаровая пневмозаслонка ∅50 "Camozzi"
- Signal amplifier - weight sensor
4 972 BYN
- ABAC 6000-270 CT7,5 Compressor assembly
- Manufacturer - ABAC (Italy)
- Receiver - 270 liters
- Performance 827 l min
- Power - 5.5 kW
- Режим работы полностью автоматический "одна" кнопка
- Buffer for storing concrete recipes in memory - 200 pieces
- Software: accounting of material consumption and equipment operation
- Контроллер "Omron" (Япония) серии CP1L
- Сенсорная панель управления "Omron" (Япония) серии NB. Диагональ 10,1 дюйма, широкий угол обзора, TFT-экран, 65 000 цветов.
- The control system to achieve homogeneity of the mixture and its mobility
- Transcend Flash Drive 4Gb
- Сontrol panel case protection - IP54
- Power cabinet case protection - IP54
- The control, protection and switching equipment «Schneider Electric» (France)
- Manual control panel with ingress protection buttons on mimic panel
- Set of diagrams and instruction manual
3 993 BYN
- operator cabin built (coating: zinc)
- Gangway (coating: zinc)
- Sound insulation, protection against rain
- Three viewing windows (PVC, double glazed windows), insulated door with lock
- Lighting
- Hardware for assembly RBU: metering complex overpass screw silage
- Hardware, accessories
- Wire for screw fixing
- Kit for connecting the database (pnevmotruba, sleeves, bends, RVC 51-70 clamps, duct PVC-5-C-60)
- Limit switch for the database
- Kit vodopodvedeniya (pipe bends, sleeves, T-joints, anchor bolts, brackets)
- Kit RBU pneumatic (air tubing, pnevmotruba, fittings, hardware)
- Set of cables
- Couplings (5 titles)
- compactor
- Acid sealant TempPlus
- Power and control cables, protected by metal hose (in mobile plants they are laid in frame)
- Set of locking sensors and executing mechanisms position sensors (skip, mixer's gate, etc.)
3 441 BYN
- Lattice with section 100x100 (70x70). Cell height 70 mm. Weight 575 kg
1 007 BYN
- Aeration nozzle IF-001-12 8pcs
- Assembly kit (fittings, tees, polyurethane tube, bracket, nipple, gasket, plug)
- CAMOZZI filter regulator 1 pc
- Ball valve G1 / 4 1 pc
- Axial pressure gauge, 0-12 bar 1pc
- 3/2 distributor CAMOZZI, G1 / 4, one-way. 1 PC
- Solenoid CAMOZZI A7E (220V-AC) 1pc
- A70 and G70 solenoid connector 122-800 1 pc
9 036 BYN
- Фильтр цемента MAXAIR-24
- overpressure relief valve VDS273
- Cement level sensor RLB110 - 2 pcs.
- The shutter disk VFA300-LT
- OLI MVE 300/3 Vibrator
359 BYN
- safety valve
- Adjusting ring
- Material - Carbon Steel
- Compound - a collar
- Passport to Safety Valve
5 631 BYN
- Фильтр цемента "MAXAIR-24" в сборе (Италия)
- Cartridges pneumatic cleaning system
- Operational documentation
679 BYN
- Valve VDS273 overpressure relief assembly
- Adjusting ring
- Operational documentation
872 BYN
- RLB cement level indicator assembly
- Adjusting ring
- Operational documentation
- The shutter disk VFA300-LT
- Handle for gate control
- Operational documentation
310 BYN
- Vibrator assembly, packed
- Disturbing force - 321 kg
- Machinery certificate
752 BYN
- CALPEDA MXH 202E Pump assembly (Italy) for chemical agents supply
- Capacity - 80 liters/min
- Power - 0.33 kW
- Weight - 6.9 kg with packaging
- Machinery certificate
26 010 BYN
- Silo Tank (V = 68 m3): cover - 4 sectors, cylindrical sections - 16 pcs, large cone - 4 sectors, small cone
- Mounting frame
- Stairs
- Cover protection enclosure - 11 sectors
- Loading pipe d 102 with connection lock
- Connecting flanges for installation cement filter emergency valve, level sensors, aeration and vibrator
- Shot peening prior to application to the extent Sa 2 1/2 GOST P ISO 8501-1-2014
- Corrosion protection is made of two-component priming enamel based polyurethane-acrylic resin production Lankwitzer (Germany) in the spray-drying chamber ATIS
- Frame for transportation
- Hardware for the assembly of a silo
- Polyurethane sealant Soudaflex FC 40 gray 600 ml - 10 tubes
- Machinery certificate
12 272 BYN
- Шнек "SCUTTI" (Италия) в сборе
- Pipe Diameter 219 mm Pipe Length 11 to 500 mm (sectional consists of four parts 3, 2.2, 3.7 and 2.98 meter connects flange)
- Привод: мотор-редуктор "SIEMENS" (Германия). Мощность 15 кВт, 300 об\мин
- The balanced shaft with spiral tselnovitoy
- Inlet connection - Adjustable Balloon
- Inspection window for cleaning and maintenance
- Shot peening, epoxy primer, acrylic-polyurethane enamel. Thickness: 100 microns
- Operational documentation
Concrete plant QUICK BETON-55 - is a compact tape factory, manufactured by ZZBO.
QB-55 продолжает линейку бетонных заводов производительностью 55 куб.м бетона/час, 75 куб.м бетона/час, 95 куб.м бетона/час. Это быстромонтируемые РБУ, не требующие подготовки высокопрочной поверхности для его установки, а так же с возможностью установки рамного шасси для более мобильной эксплуатации.
Onsite QUICK BETON-55 mobile concrete plant, with capacity up to 55 cubic meters of concrete per hour.
Перевозка в одном 40 тонном контейнере или еврофуре. Борта дозирующего комплекса складываются и перевозятся в отдельной транспортировочной кроватке.
The plant is supplied already fully prepared for the work, does not require a long setup and preparation of the foundation.
It is set in the open air, any dense surface without preparation or any room with a ceiling height of not less than 9.5 meters.
Start-up: connection to 380 V voltage supply and water feed. It takes less than two hours!
The principle of automatic operation:
- Инертные (песок, отсев, щебень и прочее), которые будут использоваться в производстве бетонараствора, распределяются по отсекам бункера инертных по наименованию. Количество бункеров равняется 4 шт. Таким же образом, распределяются по классу цемент в силосе, вода и добавочные вещества в расходные баки.
- After selection of a particular concrete formula, there needed to input the required volume (m3). After this the process of production starts.
- Inert materials are batched separately according to set weight. The batching is performed on the belt conveyor on which they are fed by opening of the hopper's gate.
- Batched inert materials are loaded into the mixer on this weigh belt conveyor.
- Cement, water and various chemical additives are fed to the corresponding dispensers where they are weighted according to the formula specified in the automation system.
- After dosing of all components of the concrete turns the solution through a metering valve fed into the mixer.
- The mixture of all components is mixed in the mixer double shaft for a certain time and as a concrete solution is supplied through the drain valve mixer.
Twin-shaft mixer PD-2G-1200.
Twin-shaft concrete mixer consists of a stationary welded body with two horizontal shafts with spokes and arms located inside. The shafts are joined by a synchronizing device to protect the drive. Mixture components are loaded directly into the mixer box which is protected from foreign particles by a protecting grid.
Is driven by an electric motor with power of 30 kW through the belt drive, equipped with a jacket and a powerful crane reducer. Mixing shaft rotation speed 36 rotations per minuteMixer box is coated from the inside by wear-resistant armor, flake type. . Броня сменная, крепится на винты. Броня чешуйчатого типа, состоящая из элементов, позволяет менять только износившуюся часть брони, что облегчает ремонт и обслуживание. Выгрузка готовой бетонной смеси из двухвального бетоносмесителя производится через окно в днище корпуса, закрываемое двойным секторным затвором with pnevmozatvorom "Camozzi" (Italy).
In one cycle is made 0.8 concrete cube. The cycle lasts about 40 seconds. Thus, one and a half minutes of installing QUICK BETON-55 produced 1.7 concrete cube.
DK-40 metering hopper
Обладает большой вместимостью 40 кубов инертных материалов. Это четыре бункера объемом по 10 куб. метров.
Большая загрузочная ширина бункеров — 3,5 метра Конвейер снабжен шевронной лентой и футерованным барабаном, системой антисползания и самоочистки. Конвейер весовой, на подвесных тензодатчиках CAS (Ю. Корея). Погрешность дозации 1%.
Power conveyor drive 18.5 kW.
Бункера снабжены четырьмя задвижками на пневматике Camozzi. На конусе бункеров установлены восемь вибрдвигателей Oli, закрепленных на специальной платформе, закрепленной через четыре виброподушки стенки конуса бункера, воздействие вибрации на инертный материал происходит с помощью вибропластины не контактирующей со стенкой бункера. Снижено воздействие механической разрушительной силы на сварные соединения смежных конструкций.
BD-45 Block of Dispensers
Блок дозаторов состоит из рамы, бункера (дозатора) цемента, дозирующего бака воды с насосом, дозирующего бака жидкостных хим. добавок.
Рама сборно-сварная из стали. Дозирующий бак снизу восьмиугольной, сверху четырех угольной формы, образованный пирамидой и ее сечением, сварен из листовой стали. Бункер цемента подвешивается на трех тензодатчиках BSA-500L, также являющимися измерителями массы продукта в бункере. Опора имеет 2 отверстия для крепления тензодатчиков. Бак воды с насосом и бак хим. добавок выполнены в форме прямоугольных призм. Бак воды сварной из листовой стали, бак хим. добавок сварной из нержавеющей стали.
Бак воды подвешивается по такому же принципу, как и бункер цемента. Бак хим. добавок подвешивается на одном тензодатчике BСА-100L, являющимся измерителем массы жидкостной хим. добавки.
Данные с тензодатчиков обрабатываются сумматором, расположенном в распределительном шкафу. После совершения операции дозирования (наполнении баков необходимой для замеса массой цемента, воды и хим. добавки) автоматически отключается подача в баки и открываются заслонки сброса в смеситель.
Next there is complete devastation tanks.
Cement silo, piping silo and augers always in stock in Zlatoust! Producer «SCUTTI» (Italy)
Compressed air system compressor Abac B 6000/270 CT 7.5
Состоит из итальянского поршневого компрессора Abac B 6000/270 CT 7,5 и пневмосистемы Camozzi. Производительность 827 литров в минуту, мощностью 5,5 Квт. Давление 11 атм. Ресивер 270литров. Компрессор уже встроен в раму и защищен от внешней среды и пыли.
Automatic remote control PA2.0 "one button"
С помощью системы автоматизации «ПА 2.0» можно управлять бетонным заводом, в ручном и полуавтоматическом режиме работы, используемых для отладки оборудования и отработки рецептов выпускаемой продукции. А также в автоматическом режиме по принципу «одна кнопка», позволяющем получить заданное количество бетона, по выбранному из памяти рецепту и предустановленным параметрам работы оборудования. Расширенные настройки каждого отдельного узла, помогают подстроить работу завода под необходимый технологический процесс производства и добиться максимальной производительности в конкретных условиях производства и перестроить цикл за пару минут. Парольная защита разных уровней доступа и функция создания ежедневного отчета на USB накопитель в базовой комплектации.
Возможна поставка бетонного завода в защитном покрытии цинк. Покрытие наносится методом холодного цинкования.
- Capacity up to 55 cubic meters. meters per hour of work
- Twin-shaft mixer, cement savings up to 15% and a high quality mixture of
- Transportation in the first 40 feet container or eurowaggon
- Installed directly on site where the concrete is needed
- It does not require the preparation of the foundation, the launch of the new site in 1 hour
- Automatic operation mode - "single button" principle
- 2 year full warranty
Technical Features

Quality
certificates

Products
in stock

Individual configuration
with prices for each item

Mobile
commissioning team
available

Worldwide
delivery
in trucks or containers
Geography of deliveries 2011-2018
Own production, in-stock products and
professional team allow us guarantee
most competitive prices, shortest
possible delivery time and high-quality goods
Call the hotline in Belarus
Our managers will answer all your questions from Monday till Friday:
from 06:00 a.m. to 05:00 p.m. (GMT+3, Moscow time)
Address: The Republic of Belarus, 220037, Minsk, ul. Marevskaya, 7a, pom.1 room 9
e-mail: info@zzbo.ru

Valery Stefanovich Sivitsky
Head of sales department in Minsk
Phone: +375 (33) 395-90-16
e-mail: sivitski78@zzbo.ru

Denis Zhilyakov
Director of the branch in the Republic of Belarus
Phone: +7-351-900-90-16
e-mail: 9009016@zzbo.ru
Place your order
We will send you the price,
conditions and terms of delivery

Response within 1 hour

You will get the offer with
individual delivery and payment conditions